3 Ways to Remove a Stuck or Broken Bleeder Screw

You may find a frozen or broken bleeder screw that is stuck or snaps off when trying to bleed the brakes. Dissimilar metals tend to corrode and fuse together, and a steel bleeder screw and an aluminum brake caliper is one reason rust is able to bind these together so easily. Fortunately there are a few methods you can try to remove it that we cover in this article and video.

How to Remove a Broken Bleeder Screw

How to remove a bleeder screw

If the bleeder screw is broken and unable to be removed, you will need to replace the entire caliper. You can’t bleed the brakes if you can’t loosen the screw, and if you can’t bleed the brakes you aren’t going to be able to stop safely. This makes the brake caliper defective and means you’ll need a new one.

If the screw is just stuck, here are three methods you can try to remove it so it doesn’t break and snap off.

How to remove a stuck or frozen brake bleeder screw

  1. Clean the Area with a Wire Brush, Spray Rust Penetrant, Tap the Side of the Caliper with a Hammer, and Loosen and Tighten the Bolt

    Thoroughly clean the bolt with a wire brush, removing as much debris and rust as possible. At the least, this will give you less rust and contaminants to loosen and clear.

    Once the rust and corrosion is clear, apply rust penetrant. Many different kinds exist to help loosen these parts, and it’s a go-to method for many frozen parts.

    You can try to tap the edge of the brake caliper with a hammer to rattle and loosen the corrosion. Don’t use a large hammer and don’t swing too hard to not damage the caliper by cracking or breaking the aluminum. A standard claw hammer will work just fine, and lightly tap it about 20 times to try and loosen the bolt.

    Then loosen the bolt with a ratchet or smaller breaker bar. A ratchet will work fine but a smaller breaker bar also works great. Try to crack the screw loose, even just a little. Then tighten it up a little. Keep loosening and tightening the bolt, and try to get the screw to crack loose. If it moves, take your time and apply more oil as needed. This should help clear and loosen the rust and corrosion that is binding the screw to the caliper.

  2. Remove the Bolt with an Air Hammer

    An air hammer will act like an impact tool but give you more control. An impact tool will twist upon contact, which can strip or break the bleeder valve, but an air hammer will send a steady vibration to hopefully crack and loosen the corrosion to break the bolt free. Then you can attach a wrench to the bit at the same time to start rotating it at your own pace.

    Wear safety glasses and hearing protection, and use an impact socket when using impact tools. If you use a chrome socket, it can break and shatter. A rounded bolt removal socket can help with this also. Its design will cut into the edges of the bolt to help grip and turn it. You may need to tap the socket on with a hammer.

  3. Heat the Area with a Blow Torch, and Loosen the Screw with Vise Grips and a Hammer

    If you used any rust penetrant, wipe it off with a cloth and any other grease or oil in the area. Since the brake caliper is made of aluminum, has rubber boots, and brake fluid inside, you don’t want to use too much heat, but heat can loosen the bolt. Heat the base where the threads go into the caliper. This will expand the opening and reduce tension on the threads. Do not heat the actual screw. Heating the bolt directly will cause it to stick tighter. Heat this area for some time, around a minute.

    This next step may work with or without head applied. Clip vise grips to the screw tightly and tap the end of the handle with a hammer to loosen the bolt. Try removing the bolt with a socket and ratchet again, but be careful because the caliper will be hot. Heat the caliper more if needed.

What to Do If You Removed the Broken Bleeder Valve

If you removed the bleeder screw, install a new one. If you can’t remove it, you’ll need to replace the entire caliper.

Fix a broken bleeder screw yourself with quality auto parts at 1aauto.com

DIY Tips: Replace Parts on Your Car

Find out how to replace parts on your own car with our how-to videos. We have thousands of how-to videos for many makes and models covering diagnostics and installation instructions for many parts.

Learn More Tips

Shop Parts and Tools

Summary
3 Ways to Remove a Stuck or Broken Bleeder Screw - 1A Auto
Article Name
3 Ways to Remove a Stuck or Broken Bleeder Screw - 1A Auto
Description
If you tried to loosen the bleeder valve and it's stuck or frozen, this guide and video reveals 3 ways to remove a broken bleeder screw yourself and what to do if you can't remove it
Author
Publisher Name
1A Auto
Publisher Logo

Leave a Reply

Your email address will not be published. Required fields are marked *